a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. part no. AL-00-2OR1CT diff no. high power type led lamps 1 ? package dimension: notes: 1. all dimensions are in millimeter. 2. an epoxy meniscus may extend about. 1.5mm(0.059") down to the lead 3. tolerances unless dimension 0.25mm.
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. part no. AL-00-2OR1CT diff no. high power type led lamps 2 chip led parts p/n. material emitted color lens color AL-00-2OR1CT algainp super red water clear ? absolute maximum ratings at ta=25 parameter symbol rating unit continuous forward current i f 60 ma operating temperature topr -25 to +80 storage temperature tstg -40 to +100 soldering temperature tsol 260 5 electrostatic discharge esd 1000 v power dissipation p d 180 mw peak forward current duty 1/10@1khz i f peak 100 ma reverse voltage v r 5 v ? electronic optical characteristics : parameter symbol min. typ. max. unit condition luminous intensity i v 700 1000 mcd i f =60ma viewing angle 2 1/2 150 deg i f =60ma peak wavelength p 630 nm i f =60ma dominant wavelength d 620 625 630 nm i f =60ma spectrum radiation bandwidth 30 nm i f =60ma forward voltage v f 1.8 2.2 2.8 v i f =60ma reverse current i r 10 a v r =5v
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. part no. AL-00-2OR1CT diff no. high power type led lamps 3 ? reliability test items and conditions : the reliability of products shall be satisfied with items listed below. confidence level: 90% ltpd: 10% no item test conditions test hours/cycle sample q?ty ac/re 1 solder heat temp 260 5 5 sec 80 pcs 0/1 h +85 30min 5min 2 temperature cycle l -40 30min 100 cycles 80 pcs 0/1 h +100 5min 10sec 3 thermal shock l -10 5min 100 cycles 80 pcs 0/1 4 high temperature storage ta=100 1000 hrs 80 pcs 0/1 5 low temperature storage ta=-40 1000 hrs 80 pcs 0/1 6 dc operating life temp 25 i f =20ma 1000 hrs 80 pcs 0/1 7 high temperature high humidity 85 85%rh 1000 hrs 80 pcs 0/1
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. part no. AL-00-2OR1CT diff no. high power type led lamps 4
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. part no. AL-00-2OR1CT diff no. high power type led lamps 5
a a a - - - b b b r r r i i i g g g h h h t t t a-bright industrial co., ltd. part no. AL-00-2OR1CT diff no. high power type led lamps 6 precautions for use 1. over-current proof customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (burn out will happen). 2. storage 2.1 do not open moisture proof bag before the products are ready to use. 2.2 before opening the package, the leds should be kept at 30 or less and 90%rh or less. 2.3 the leds should be used within a year. 2.4 after opening the package, the leds should be kept at 30 or less and 70%rh or less. 2.5 the leds should be used within 168 hours (7 days) after opening the package. 2.6 if the moisture absorbent material (silica gel) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment U 60 5 for 24 hours. 3. soldering condition 3.1 pb-free solder temperature profile 3.2 reflow soldering should not be done more than two times. 3.3 when soldering, do not put stress on the leds during heating. 3.4 after soldering, do not warp the circuit board. 4. soldering iron each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than soldering iron capacity 25w. leave two seconds and more intervals, and do soldering of each terminal. be careful because the damage of the product is often started at the time of the hand solder.
|
